Restructered pre-import

Old Pages/Byzantium/Byzantium_Sprint_2_Inventory.md

@@ -0,0 +1,98 @@
+Add the crap you have to this list even if someone else says they have
+the same stuff.
+
+Also, keep in mind that having spares around would be handy in case we
+fry some stuff.
+
+## haxwithaxe (chris)
+
+- openwrt compatable routers....10
+- FRS/GMRS handsets....2
+- laser pointers....1
+- webcams(in laptops)....2
+- usb webcams....1(non hackable :( )
+- microcontrollers....5
+  - teensy 2.0
+  - teensy++ 2.0
+  - mbed
+  - 2 jeenode v4
+- photoresistor....(will buy \$20 worth before planing meeting \#2 ...
+  radioshack is cheaper than digikey ... who'da thunk)
+  - Things are weird like that these days.
+- 7805....(will buy \$20 worth before planning meeting \#2 ... again ...
+  wtf radioshack is cheaper)
+  - Cheaper but more scarce. Buy them online, you'll have a better
+    chance of getting them, plus it saves on gas.
+
+## The Doctor
+
+- Wireless routers: 2
+- FRS/GMRS handsets: three pairs
+  - Uniden GMR1235-2: one pair
+    - No headphone or mic jacks.
+    - Will have to drill into case and patch directly onto PCB.
+    - Will have to build a push-to-talk circuit, though we might be able
+      to get away with using two per node (one sending, one receiving,
+      on different channels).
+  - Audiovox GMRS602: three (one is still MIA, I think ITechGeek has it)
+    - [Manual](http://audiovox2.info/docs/common/GMRS602CH/GMRS602CH_OM.pdf)
+    - Has vox support.
+    - Has a combination headphone/mic jack.
+    - No hardware modifications will be required.
+    - Simplex operation.
+    - Supports CTCSS subcodes to multiplex channels.
+    - Plug pinout (held with the tip downward)
+      - Center: base of plug : common
+      - Left: middle of plug : phono
+      - Right: tip of plug : mic
+- Walkie-talkies: 2, could get another pair, they're cheap
+  - Each uses a 9V battery
+- Laser pointers: 4
+  - See Make Magazine \#16, Spy lasercomm device.
+  - Simple design.
+  - Exposed power leads by chopping up casings last night.
+  - Two work well, one is kind of dodgy, one appears to be DOA.
+  - Taped buttons down.
+  - Taped stacks of coin cells together.
+  - Spring is negative, inside of shell is positive.
+- Assorted LEDs: 20
+- Webcams (USB): 1
+- Microcontrollers: 1 Arduino Diecimiela
+- Photocells: need to order
+- Photoresistors: Seven, need to order more
+- Modems: 2
+- TinyTrak 4 (used with Project Spaceblimp)
+- Radio Shack HTX-200 HT
+- Uniden BC92XLT scanner
+- Encapsulated solar cells, 66mm x 95mm x 6mm
+  - Pre-wired, with exposed holes for probes as well.
+  - 0.5V @ 800mA: 1
+    - Didn't generate an appreciable amount of current last night.
+    - Physically larger than the other one.
+    - Might be unsuitable for use as a detector.
+  - 1.0V @ 200mA: 1
+    - Generates a decent amount of current.
+    - Reacted to room lighting and flashlight in the 'space last night.
+    - Might make a good optical sensor.
+- High intensity white light LED flashlights (miniature): 2
+  - I've had this model open and played around with them a bit, they're
+    just high-intensity white light LEDs that run on 3VDC. We'll have
+    more trouble opening the casings than putting them to use.
+- 1/8" monoaural phono plugs: 4
+  - Useful for plugging into laptops.
+- 1/8" stereo phono plugs: 4
+  - Useful for plugging into radios.
+- 14" jumper leads, with alligator clips on both ends: 10
+- Audio output transformers, 1K ohms in, 8K ohms out (RS 273-1380): 4
+- Assorted resistors, carbon film type, 1/4 watt, 5% tolerance: 500
+  - Note: this was the only way I could find the resistors needed to
+    build the lasercomm device. Fraggin' Radio Shack...
+- Ultra-high brightness red LEDs, 10mm diameter: 4
+- 7805 voltage regulator, 5 VDC, 1A: 3
+- Assorted cadmium sulfide photocells (RS 276-1657): 5
+- assorted rubber bands to hold transmit buttons down
+- assorted six inch lengths of heatshrink tubing to protect wiring
+  splices, bundle coin cells into ad-hoc power packs
+- batteries for hand-helds
+- 741 op amp, mini DIP formfactor, 8 pins: 4
+  - could use these to build amplifiers