FL-176 LF RFID RX (#248)

* pulldown ibutton pin during rfid read
* enable and handle COMP interrupts
* send events from comparator IRQ and handle in app
* manchester encode
* successfully read em4100
* read-emulate
* led

firmware/targets/f3/f3.ioc

@@ -17,8 +17,10 @@ VP_RTC_VS_RTC_Activate.Mode=RTC_Enabled
 RCC.RTCFreq_Value=32768
 PA3.GPIOParameters=GPIO_Speed,PinState,GPIO_Label,GPIO_ModeDefaultOutputPP
 PA6.GPIO_Label=PA6
+COMP1.Hysteresis=COMP_HYSTERESIS_HIGH
 PD0.Locked=true
 PC5.Mode=INP
+VP_COMP1_VS_VREFINT14.Signal=COMP1_VS_VREFINT14
 USART1.IPParameters=VirtualMode-Asynchronous
 PA3.GPIO_Speed=GPIO_SPEED_FREQ_LOW
 PB13.Signal=TIM1_CH1N
@@ -37,6 +39,7 @@ SPI1.Direction=SPI_DIRECTION_2LINES
 TIM2.IPParameters=Channel-Input_Capture1_from_TI1,ICPolarity_CH1,AutoReloadPreload,Prescaler,Channel-Input_Capture2_from_TI1
 RCC.APB2TimFreq_Value=64000000
 PCC.Ble.PowerLevel=Min
+COMP1.Mode=COMP_POWERMODE_MEDIUMSPEED
 PB6.Signal=USART1_TX
 PB6.Mode=Asynchronous
 SPI1.CalculateBaudRate=4.0 MBits/s
@@ -175,7 +178,7 @@ Mcu.Pin50=PB6
 Mcu.Pin55=VP_FREERTOS_VS_CMSIS_V2
 Mcu.Pin56=VP_HSEM_VS_HSEM
 Mcu.Pin53=VP_ADC1_Vref_Input
-Mcu.Pin54=VP_COMP1_VS_VREFINT12
+Mcu.Pin54=VP_COMP1_VS_VREFINT14
 PC6.Locked=true
 PA9.Signal=I2C1_SCL
 VP_TIM1_VS_ClockSourceINT.Signal=TIM1_VS_ClockSourceINT
@@ -216,6 +219,7 @@ RCC.RNGFreq_Value=32000
 PC2.GPIOParameters=GPIO_PuPd,GPIO_Label,GPIO_ModeDefaultEXTI
 VP_ADC1_TempSens_Input.Signal=ADC1_TempSens_Input
 Mcu.Pin30=PE4
+NVIC.COMP_IRQn=true\:5\:0\:true\:false\:true\:false\:false\:true
 PA1.GPIO_Label=LED_RED
 Mcu.Pin33=PB14
 Mcu.Pin34=PB15
@@ -312,7 +316,6 @@ PA11.Mode=Device
 PB0.GPIO_Label=DISPLAY_RST
 VP_RTC_VS_RTC_Calendar.Signal=RTC_VS_RTC_Calendar
 PB11.GPIO_PuPd=GPIO_PULLUP
-VP_COMP1_VS_VREFINT12.Signal=COMP1_VS_VREFINT12
 PC13.GPIO_Label=BUTTON_BACK
 PB13.GPIO_Label=RFID_OUT
 PB11.Signal=GPXTI11
@@ -401,7 +404,6 @@ PE4.Signal=GPIO_Output
 PB0.Locked=true
 FREERTOS.configTOTAL_HEAP_SIZE=40960
 PC14-OSC32_IN.GPIOParameters=GPIO_Label
-VP_COMP1_VS_VREFINT12.Mode=VREFINT_12
 ProjectManager.ProjectName=f3
 RCC.APB3Freq_Value=16000000
 PA6.Signal=GPIO_Analog
@@ -426,6 +428,7 @@ OSC_IN.GPIO_Label=QUARTZ_32KHZ_IN
 PC2.GPIO_Label=BUTTON_OK
 PC14-OSC32_IN.Locked=true
 PA12.GPIO_Speed=GPIO_SPEED_FREQ_VERY_HIGH
+COMP1.TriggerMode=COMP_TRIGGERMODE_IT_RISING_FALLING
 PB15.Locked=true
 PB3.Locked=true
 PB4.Signal=SPI1_MISO
@@ -463,6 +466,7 @@ PC12.GPIOParameters=GPIO_Speed,PinState,GPIO_Label
 USART1.VirtualMode-Asynchronous=VM_ASYNC
 PA13.Signal=SYS_JTMS-SWDIO
 FREERTOS.configUSE_IDLE_HOOK=1
+VP_COMP1_VS_VREFINT14.Mode=VREFINT_14
 PA9.Mode=I2C
 TIM1.Channel-Output\ Compare1\ CH1N=TIM_CHANNEL_1
 FREERTOS.configRECORD_STACK_HIGH_ADDRESS=1
@@ -492,6 +496,7 @@ TIM16.Period=291
 NVIC.SavedSystickIrqHandlerGenerated=true
 RCC.APB2Freq_Value=64000000
 PC11.PinState=GPIO_PIN_SET
+COMP1.IPParameters=TriggerMode,Hysteresis,Mode
 MxCube.Version=6.0.1
 VP_TIM2_VS_ClockSourceINT.Mode=Internal
 PC13.GPIOParameters=GPIO_PuPd,GPIO_Label,GPIO_ModeDefaultEXTI